https://www.facebook.com/illusonic

https://www.linkedin.com/company/illusonic

It has been a great show.

Hardware:

– Illusonic IAP 8

– 2x Klangwerk Phil as main stereo loudspeakers

– 2x Klangwerk Muro for wide stereo

– Our amazing subwoofer with membrane control

– Thorens

– Roon Nucleus, iPad

Point of demo:

Extend a stereo system with subwoofer and wide stereo.
Extremely spatial sound stage, yet precise. Live sound feeling.

Works on all kinds of music and sources.

Teaser video below.

Fotos by and © Rudolf Moser, Zürich

After previous Clarity extreme tests (in terms of room size and reverberance), in University of Zurich Lichthof and Aula room, we had the opportunity to test Clarity for live speech application in St. Jakob-Park Stadium in Basel.

The stadium’s PA was measured to several microphone positions. Additionally, it was measured via a NTI talkbox and wireless microphone to simulate real world condistions. Based on the measurements we did configure Clarity, which run on a Raspberry Pi 3B with 2ms latency.

Surprisingly, the effect of Clarity on the speech was more pronounced than in the previous extreme tests. An ad hoc STI measurement (STIPA) showed a significant improvement!

Based on feedback on this test, we

Optimize Clarity for speech to prevent that it sounds sometimes a bit chopped-up (merely a tuning question, we did indeed tune it aggressively, or adding a decay parameter for limiting decay speed?).

Add network audio to the Raspberry Pi 3B to facilitate integration of it into PA systems (for this test we used analogue i/o).

IAP 9.1 Firmware/Software Update

Do you love the precision of stereo, but miss immersion of surround? Then Wide-Stereo is something for you, supported by all IAPs with more than two channels. Wide stereo can be implemented with 4 or more loudspeakers.

Due to great feedback from our customers, partners, and dealers after 9.0 release with Wide-Stereo, we focused on this feature and are updating IAP 4, IAP 8, and IAP 16 with supporting features.

With this, you can get breathtaking advance over stereo, without giving up your beloved Stereo Phantom Centre. Surely, if you have it already, you can use your Centre loudspeaker with it, too.

Besides this, there are many other small improvemnents.

Download here.

Changelog compared to preivous IAP 9.0

IAP Firmware

update wide stereo with side eq to make it less bright

update wide stereo with separate center and width parameters

update wide stereo that it also works with multichannel input

iap4: add 4-II loudspeaker setup

iap8: add 4-II, 5-II, 6-II, and 7-II loudspeaker setups

increased bass management XO max frequency to 1000 Hz

added Center Spk gain to ad hoc settings

bug-fix where auro6/auro8 HDMI input was not loaded from files properly (iap 2/4/8)

IAP Configuration

iap4: add 4-II loudspeaker setup

iap8: add 4-II, 5-II, 6-II, and 7-II loudspeaker setups

add new separate width control (instead of wide stereo on/off)

moved preset lowcut outside of Illusonic Processing

added Center Spk gain to ad hoc settings

fixed a bug where .iap file was not always written properly

various reliability improvements

IAP Calibration

iap4: add 4-II loudspeaker setup

iap8: add 4-II, 5-II, 6-II, and 7-II loudspeaker setups

add new separate width control (internally)

fixed a bug where .iap file was not always written properly

various reliability improvements

IAP Control (iOS)

adapt parameters to IAP 9.1

tuned sliders’ skew factors
 

IAP 9.0 Firmware/Software Update Released Today

Download:
https://www.illusonic.com/en/audio-processors/support-downloads/

A full year in the works, major IAP 9 firmware/software implements many improvements and extensions.

See images for quick overview of major new features.

The change-log below gives a list of changes and extensions over previous version.

Yet again, we have been able to propagate lastest DSP-technology-improvements to IAP (yes, signal processor of all IAPs has still been sufficient):

Immersive: half a dozen of pro-audio plugins updates are now in IAP

Pro-Acoustics/Pro-Audio: Clarity (world’s only “DSP-based absorbers”), latest version, now in IAP

A new broadcast immersive mode is optimized for film, news, TV

These main new features have been motivated by IAP-owner requests:

wide stereo: listen to stereo, with a widened stereo stage, in your multichannel setup

new preset params (lowcut, center-gain) with existing params, allow for great night, casual listening, movies presets

CHANGELOG (compared to IAP 8.4):

IAP Firmware/DSP
    - added new option “forget changes” (system menu):
        - iap will never save any changes permanently
    - added new option “volume lock” (system menu):
        - this locks volume changes via front-panel or remote control
    - improvement of center feature (eq, time-resolution, artefacts)
    - improvement of clarity (time-resolution, effectiveness)
    - new broadcast upmix feature
    - new wide stereo upmix feature
    - removed mono upmix feature
    - bug-fix where multich center input was lost when loudspeaker setup
        had no center spk
    - added new parameters to sound settings presets:
        - low cut
        - phantomcenter/center gain

    - added new option “volume lock” (system menu):
        - this locks volume changes via front-panel or remote control
    (only gen2 IAP)

    - added new option “output digital” (output menu):
        - reverts coax 2 from input to output
    (only gen2 mk2 IAP)

    - revised input source handling, more smooth now
    
    - added support for upcoming new HDMI card/chipset

    - added usb commands for ad hoc settings
    (IAP 16 wide, other models have had it already)

IAP Configuration
    -add support for new broadcast upmix feature
    -add support for new forget changes feature
    -add support for new volume lock feature
    -add support for new output digital feature
    -improve HDMI updating, removing one power down-up
    -fixed some layout problems with IAP 16 wide
    -upgraded Windows version from win32 to x86

IAP Calibration
    -reorg of complete application
    -support for new usb heatracker
    -add support for new broadcast upmix feature
    -added clock-drift correction when two different audio devices are
        used for measurement
    -upgraded Windows version from win32 to x86
 

Thanks to real-world acoustic and sound experts, Mike Utz from Zurich University UHZ and Christopher Sauder from ETH Zurich, for making this sophisticated test possible!

The historic assembly hall of university of Zurich, where Churchill gave his famous speech after world war in 1946, is acoustically not so optimal. The marble walls do not like to be covered by curtains or acoustic absorbers, they are visually too nice.

Can Illusonic Clarity measurably improve the situation?

I have been a bit sceptical (Christof, Illusonic), as I have been aware of discussions about audio quality and perceptual audio coding, and trying to measure such codecs with conventional (linear-assuming) measurement equipment.

We have measured the PA system of the hall with a small Fostex loudspeaker placed as a “speaker simulator” near the main mics. Based on this data Clarity has been optimized. Note that measuring through the speaker’s mic, includes the acoustic feedback path.

Then, speech-transmission-index (STI) was measured on several positions, throughout the hall. NTi talkbox simulated the speaker on the main mic and NTi measurement device and mic was used to estimate STI on the different positions. There has been consistent improvement between 1 and 3 points throughout the hall. In the back of the hall, where sound has been more diffuse, improvement has been larger. Amazing, cool!
 

Last Friday afternoon, we went to Zurich University’s (UZH) historic atrium (“Lichthof”) to participate in a test, comparing different loudspeakers with and without Illusonic Clarity, for live speech and music reproduction.

The different loudspeaker systems under test were:

– A: Foohn FP-22 portable speaker

– B: Foohn LX-150 line-source speaker

– C: Foohn DLI-230 dsp-controlled line-source speaker (array almost twice as long as B)

From A, B, to C was clear improvement, in terms of intelligibility and reduction of reverberance.

For Clarity, we measured two microphone positions for each loudspeaker type. Based on the measurements, we specified bass, low, mid, and high acoustic parameters, including RT60. These parameters were loaded to Raspberry Pi (Raspi), on which Clarity ran with 3 ms latency. The Raspi was connected to the mixing console via analogue.

For C, Clarity clearly reduced reverberance of the Atrium, even on all-behind positions. Clarity’s effect adds to the line array’s beamforming improvement.

For A and B, Clarity also clearly reduced reverberance at positions not far beyond reverberation radius. Once the soundfield is fully diffuse, there is nothing to win. So A worked well and was improved by Clarity up to a certain distance (approx. 1/3 of length of Atrium). B extended that maximum distance, and C had reach up to end of Atrium.
 

Clarity is our DSP-based room optimization technology, developed for nearly a decade. It optimizes a room beyond what room eq can do. It takes away parts of the source signal, which later on the room will add again. Perceptually, with Clarity, a music or PA system sounds as if the room would have more acoustic full range absorbers.

Clarity development was driven as a feature for our audio processors (IAP). A couple of years ago, we did exploratory tests in the Opernhaus Zurich, where Clarity is applied on the Studio stage (via our low delay plug-in).

Mid January a test is planned in the historic assembly hall of Zurich University. Acoustics are not satisfactory there, and acoustic treatment possibilities are very limited. We have had another request from world-renown ETH Zurich assembly hall. Though, as they were not looking for experimentation, but a device, we had to decline.

We can’t pull off another hardware device (besides IAP) and an entirely new business. But in order to small volume provide to selected venues Clarity, how can we build in low volume with low cost a hardware device?

Take a Raspberry PI 3 (Raspi), add a high quality stereo ADC and DAC and chassis. Bill of materials of USD 200 per unit! The rest of the problem is software:

1
Latency !
Usually a problem with Linux based systems. ADC and DAC connect via I2S, which is already better than USB. Then, we use Arch Linux ARM, which runs Clarity with maximum real-time priority round robin scheduler. The Arch Linux has only 14 processes running in total, so almost complete CPU is dedicated to audio processing. In order to reduce heating, the CPU is configured to run at minimum frequency (600 MHz instead of 1.4 GHz). Processing buffersize at 48 kHz is 32 samples. A daemon logs audio hick-ups. Several days of running it reported no hick-up at all. Externally measured latency is 2.7 milliseconds! This is low enough for any live application.

2
Reliablity !
The system is configured such that when starting the Raspi it will automatically start running Clarity. A daemon is monitoring it. In case audio processing crashes, it will automatically be restarted within a few seconds. Also, the Raspi may be disconnected any time from power. To mitigate risk of some data damage of its memory card, the file system is configured such that never data will be written to it. Any written data goes just to RAM.

3
Configuration and Tuning
To tune the system, a macOS/Windows/Linux software has been developed, writing a config file to the Raspi, containing all parameters. Real-time changes are possible. Parameters are permanently stored in Raspi. So it just has to power on to do its job. Besides Clarity, we also added parametric equalizers.

Let’s see, if the mentioned historic assembly halls will get substantial improvement thanks to Clarity. If yes, we have now a possibility to deliver a device that can do this job. Once this goes through well, other doors will be opened. This is iteratively working the ladder up, step by step, to possible success.
 

IAP Update 8.4

Pro Audio and Automotive projects have been the driver for update of our Immersive technologies. Dozens of Dolby Atmos music productions have used our upmix plugin for its great sounding reverb (depth, immersion) and phantom-center extractor (center). Alone since our previous IAP release, half a year ago, we did update our plug-ins three times, based on user’s needs.

With Version 8.4 we are consolidating these improvements for our IAP users. Depth and Immersion are fully revised and now allow for more effect. Clarity is more effective with less timbral change.

Download the update here.
 

Changelog (8.3 => 8.4):

adapted apps for macOS 12 and Win 11

revised Clarity, less timbral change, improved performance without tuning

revised Depth, improved early reflections, preprocessor, and equalizer

replaced Immersion, new de-correlators

sound and timbre is now similar for all supported loudspeaker setups, previously front-only setups were quite different to surround setups

orientation left, right, rear improved (depth better adapted)

fixed bug, where default presets had mono upmix on instead of off
 

IAP Update 8.3

Since the last update, we have had good progress on our immersive technology (Depth, Immersion features), being used in our upmix, binaural, plug-ins, and automotive licensable products.

We back ported these improvements to IAP SHARC DSP. Depth and Immersion have never been so nice as now. This also allowed us to make these effects a few dB stronger, while maintaining clean sound.

List of main changes:

revised dsp depth

revised dsp immersion

fixed bug, where immersion pre-delay was too large (echo effects)

fixed bug, where mono upmix could not be switched on

IAP Calibration delay trim slider now updates time plot in real-time

IAP Configuration layout improvements

Download the update here.
 

IAP Update 8.2

Feedback from our pro-audio plug-ins and a master diploma thesis on Clarity injected innovation into our IAP product line.

IAP 8.2 improves many “Illusonic” algorithms, such as depth, immersion, and clarity.

New ad hoc center gain feature allows to change gain of center, even without a center loudspeaker.

Input delay range has been increased to 300ms, satisfying even the most complex time alignment needs in home cinemas. Believe it nor not, a high end system with high end projector needed more than the previous maximum 200ms.

Besides that, IAP software has been internally modernized and runs now natively also on Macs with Apple Silicon.

Download the update here.

Farewell Concert Fabio Luisi

Opernaus Zurich, Saturaday June 19, 2021, 19:00

The livestream and video on demand will be available free of charge on the web link above from Saturday 19 June at 7pm until the end of June.

3D Sound

Viewers will be able to choose between stereo and 3D sound. The 3D sound is made for headphones listening. By directly controlling the listener’s ear input signals, an illusion of “being at the opera” is generated. Sound is recorded with an Ambisonics and other microphones and real-time processed with Illusonic’s microphone-to-3D-sound conversion audio processing software.

More details on the concert and its 3D sound can be found on opernhaus.ch

APEI Webinar

Remote Sound Tuning in Automobiles (video available)

June 9, 2021 
9:00 AM Pacific (12:00 PM Eastern)

Remote Tuning

Illusonic is maybe the company with most remote tuning experience. Almost a decade ago, we introduced the first Illusnoic Audio Processor. Shortly thereafter we introduced IAP Calibration software, with which Hi-Fi and home cinema customers measured their systems. With the same software we could remote-tune the custoomers’ systems.

Initially, remote tuning was done based on simulated frequency responses after tuning. Later, we added auralization and were so able to listen into customers’ listening room via headphones.

IAP Calibration software, specifically taylored for automotive is called CalibrationTool Automotive. It can handle up to 64 loudspekaer channels and 64 microphone positions.

Remote Tuning of Automobiles

We had already frequenty applied remote tuning to automobiles. It was mostly related to Immersive demos, for which we also linearly tuned the cars. Thanks to remote pre-tuning, we could minimize the time we had to spend with the actual car.

With the 2020/2021 Covid crisis and travel restrictions, remote tuning of automobiles quicly became a popular topic and we have seen a lot of traction in this direction.

Remote Tuning of Automobiles

During the webinar we show in real-time usage of CalibrationTool Automotive. It is shown by means of examples on how to remote tune based on data and graphs. The headphones auralization feature with head-tracking is also shown in real-time operation. During tuning, parameters are changed and simulated car sound in headphones changes immediately.

The test at Opera Zurich for stage monitoring (previous blog-item) currently can not be finished as the orchestra can’t play on-site.

A second stage inside the opera, called “Studiobühne” (“studio stage”), used for practising or performances with smaller audience, is often used with amplified voice and reproduced sound.

This room is not a lot acoustically absorbed, say, a bit more reverberant than ideally desired.

Thus ideal for a first live test of Clarity in the opera.

Will Clarity benefit reproduced sound here?

Will Clarity benefit live amplified voice?

As it is quite complicated configuring a workstation with plug-ins for minimum delay, we developed in the meantime a low-delay standalone macOS application with less than 3m total delay. This app can be used with (high quality) sound cards (analog, ADAT, MADI) and even Dante.

Michael Utz measured the studio stage with Illusonic CalibrationTool software (aka IAP Calibration) and tuned it with EQ and Clarity. Once ready, he invited us for subjective testing on-site. The real-time test was carried out with the low-delay macOS Clarity application, connected to the mixing console via Dante.

Clearly reverb in room is reduced, sound is more clear and more focused from the loudspeaker positions.

We tested speech with wireless microphones. Feedback threshold was significantly increased (4-7 dB) and speech was perceived as more clear.

That’s great! Hopefully a live-test ona real public-performance will be admitted soon! :-)

More than a year ago, we released IAP’s Immersive Upmix algorithms as a “Test Balloon Plug-In” for music producers and sound engineers. This plug-in works with workstations such as ProTools, Reaper, Cubase, and Logic.

The plug-in has been widely applied worldwide for things such as Dolby Atmos music production, applause upmix, film music, etc. The Test Ballon Plug-Ins Program has brought us a wealth of pro audio feedback. This feedback has allowed us to evolve Immersive Upmix to a great degree.

Now we deliver latest Immersive Upmix, same as in latest plug-in, to our IAP customers via IAP 8.1 Firmware/Software update. Free of charge.

Additionally, the update incorporates many more improvements and bug fixes.

Download the update here.

Change Log (since 8.0..4):

IAP Firmware:

major update to Depth

major update to Immersion

got rid of dry center

new mono upmix option

improved LRC quality

improved Clarity time resolution

IAP Configuration:

added new mono upmix option, and removed dry center

added volume and mute control

kept macOS minimum requirement at 10.6

IAP Calibration:

improved Clarity optimization algorithm

extended Clarity visualization,

added new mono upmix option, and removed dry center

dozens of small improvements

set macOS minimum requirement to 10.11 (from 10.6)

bug fixes